Shane welding  |
Structural steel welding  |
Shane welding on a trailer that we modified so it would fit this boat.  |
Aluminum weld  |
 |
This is a pontoon boat that we welded a complete frame for.  |
This set-up is used to distribute bentanite (sealant for stock ponds) . It's the only one like it!  |
Finishing assembly on frame.  |
Pontoon boat with flotation and deck installed.  |
When you can't find hinges, you make em! These were a set of hinges made for a 70's model Glaston engine hatch. The boat owner couldn't find them, so we made them.  |
This is a crane that we fabricated to lower a metal cage and water pump unit out at Lake Travis in the Coeur du Lac development.  |
It's a long way down!! 40 ft to be exact. Hold on J.R.!!  |
 |
This is a (before paint)view of the custom hatch door for the Donzi  |
aluminum bracket  |
 |
Sterling kit car- View from above of the tray to hold the airbag compressor and components...  |
View of welding area....where the metal magic happens  |
bracket for custom swim platform  |
one of Shane's beautiful welds  |
 |
Custom teak swim platform for a 1996 Donzi  |
 |
Side view of outer step-up bracket with non-skid for a no slip grip  |
 |
Overhead view  |
 |
This was a gate built for a customer.  |
Custom gate  |
making gate scrolls  |
finished gate  |
 |
|
|
|
|
original logo  |
This is a 1967 Sweet 16 Donzi Runabout. In for a complete restoration and color change.  |
 |
 |
Updated from a 270 Volvo outdrive "original" to a late model Alfa drive with new lathom hydrolic steering (not yet installed) trim-tabs (not yet installed)  |
Interior: Before  |
Upgraded from original Ford 302 two- barrel to a late model 351 Ford Windsor small block.  |
Motor prepped for paint  |
Descaling & prepping for paint  |
Motor ready for exhaust and new tins  |
Minor boat "rhinoplasty" (nose job)  |
AFTER: Repair to nose of boat.  |
Nose job: after  |
Transom repairs interior and exterior  |
Suspended in preparation for hull repair and prep  |
Top of boat primed and ready for paint and ski locker reinforced  |
Interior prep for paint and carpet  |
Bottom of deck lid. Repairs complete and primed- ready for paint.  |
Before: Start of repair on engine cover  |
During: Shane made the mold for these blisters and added this nice custom touch to the engine cover  |
engine hatch being prepped for paint and final assembly of shaker scoop  |
Complete custom deck with shaker hood scoop and teardrop blisters  |
Custom fuel tank  |
Custom fuel tank  |
Top of boat getting hardware areas prepped for paint and assembly.  |
A view from the underside of the dash showing wiring layout and stereo components.  |
An inside view of one of the speakers and some of the gauges being pre fitted.  |
 |
 |
bottom half of boat almost complete. Stripes soon to come...  |
Red powdercoat replaces the old yellow paint on the trailer  |
 |
 |
 |
 |
 |
Can you say fast???  |
 |
 |
behind dash  |
primed and ready for paint  |
 |
front view
 |
 |
 |
Rear view (before final paint and assembly)  |
Rear view (after)  |
Her new colors..  |
 |
Final fitting of the custom interior  |
Custom control panel  |
Proud new owner of the Donzi  |
right before her first time out with her new owner in Louisiana...  |
|
These are racing seats that we tore apart to make custom fit the car and customer.  |
This is what's left of the original $700 seats! Anybody need a seat cover?  |
This is the finished product  |
 |
Customers new 2110cc built specifically for this application  |
 |
 |
New motor disassembled for paint.  |
One of many prefits for the motor  |
 |
Initial tear down  |
 |
Semi finished front end with new grafted-in Porshe headlights  |
 |
Back of car before mods were made  |
 |
The first visit to pick up the car  |
Before  |
welding floor pans  |
We joined the body pieces together so there will be no seams.  |
rear view- bodywork  |
 |
1st primer. It's actually looking like a car!  |
This a shelf to hold the compressor tank etc.  |
with her airbags installed she sits nicely on her new shoes  |
 |
|
|
|
|
Demo of floor  |
 |
Tahiti floor and stringer replacement  |
BEFORE: This boat's floor was rotted. We are re-doing parts of the floor and all of the interior.  |
AFTER: These are the same seats and base in the previous picture re-upholstered and recarpeted.  |
AFTER: This is another view of the re-upholstered seats.  |
AFTER: This is the sun pad at the back of this boat beautifully re-upholstered.  |
This Correct Craft Ski Natique needed a complete stringer job.  |
 |
 |
 |
BEFORE: Larson floor  |
AFTER: Replaced rotted floor and re carpeted this Larson  |
BEFORE: This is what it looked like when our customer brought it to us.  |
AFTER. Hook 'em! No more blue/white/black here!
The owner of this boat also owns Longhorn Towing. See a theme here??
 |
BEFORE: This Coreect Craft Ski Nautique floor has extensive water damage. The whole floor and stringers in this boat will be redone along with wiring and interior carpeting.  |
Correct Craft cleaned out and new stringers being put in....  |
Ski Natique: We reworked the motor here  |
Correct Craft: first motor refit  |
AFTER: Correct Craft Ski Nautique with new carpet, gauges, battery cover with driver side access, and rework of some interior pieces.  |
After: Correct Craft Skin Nautique view from above of interior  |
BEFORE: this swim platform was a little weather worn and needed a freshen up....  |
AFTER: with new shine she's ready for her first dive!  |
18' Sea Ray boat in need of new floor. BEFORE  |
18' Sea Ray floor... AFTER with new flooring and carpet  |
BEFORE. We did a partial floor repair on this Larson.  |
 |
we replaced the floor and installed new carpet  |
AFTER: When this boat came to us the interior was mostly rotted away. We replaced the pads shown here.  |
 |
Project: Install remote LED lighting and relocated license plate.  |
Project: Took an after market pipe and removed 4.5in. in length and reassembled for a deeper and "more manly" sound.  |
customer with bike  |
rear view  |
 |
 |
Go Kevin go!  |
When riding normal just isn't a good enough view.....  |
Vintage BSA came from up North. We made a custom "period correct" air box. We also tuned the motor and made other adjustments.  |
 |
 |
This is a total resto Harley  |
New vs. old (holding old)  |
This is a custom air cleaner cover by MSM  |
 |
 |
Custom fab  |
 |
Another great paint job!! This is the tank to "Rob's" bike before it left for Sturgis.  |
This is the Harley that the black tank in the previous picture belongs to.  |
and he's off! Sturgis 2006 & 2007  |
Shane sanding in preparation for paint on a "cow catcher" for a bike  |
|
|
Our sign...  |
Owners: Sasha and Shane  |
Come on in!  |
Hook 'em!  |
Our boat....who's that guy???  |
This is what started it all for me!! This was my dad's boat. The Amigo II.  |
The Amigo II  |
Sasha carpeting bunks for a boat trailer  |
This is a photo sent to us by an Army friend out of CA. He is a boat mechanic out there. Keeping our guys safe on the water! God bless our troops.  |
Getting ready to unload  |
A little closer shot of the Army boats.  |
Being on the water runs in our blood! Our grandfather fishing in East Texas.  |
Dean hard at work on the 442  |
back in the day when Shane started in the body shop biz....  |
We finally gave Brad's boat a name and new TX numbers. No more bad luck!  |
|
|
|
